This file contains radio driver code. More...
#include <stdint.h>#include <stdbool.h>#include "at86rf230_registermap.h"#include "hal.h"Go to the source code of this file.
Defines | |
| #define | RF230_MAX_TX_FRAME_LENGTH ( 127 ) |
| 127 Byte PSDU. | |
| #define | RADIO_STATUS_START_VALUE ( 0x40 ) |
| This macro defines the start value for the RADIO_* status constants. | |
Transaction status codes | |
| #define | TRAC_SUCCESS 0 |
| #define | TRAC_SUCCESS_DATA_PENDING 1 |
| #define | TRAC_SUCCESS_WAIT_FOR_ACK 2 |
| #define | TRAC_CHANNEL_ACCESS_FAILURE 3 |
| #define | TRAC_NO_ACK 5 |
| #define | TRAC_INVALID 7 |
Enumerations | |
| enum | radio_status_t { RADIO_SUCCESS = RADIO_STATUS_START_VALUE, RADIO_UNSUPPORTED_DEVICE, RADIO_INVALID_ARGUMENT, RADIO_TIMED_OUT, RADIO_WRONG_STATE, RADIO_BUSY_STATE, RADIO_STATE_TRANSITION_FAILED, RADIO_CCA_IDLE, RADIO_CCA_BUSY, RADIO_TRX_BUSY, RADIO_BAT_LOW, RADIO_BAT_OK, RADIO_CRC_FAILED, RADIO_CHANNEL_ACCESS_FAILURE, RADIO_NO_ACK, RADIO_SUCCESS = RADIO_STATUS_START_VALUE, RADIO_UNSUPPORTED_DEVICE, RADIO_INVALID_ARGUMENT, RADIO_TIMED_OUT, RADIO_WRONG_STATE, RADIO_BUSY_STATE, RADIO_STATE_TRANSITION_FAILED, RADIO_CCA_IDLE, RADIO_CCA_BUSY, RADIO_TRX_BUSY, RADIO_BAT_LOW, RADIO_BAT_OK, RADIO_CRC_FAILED, RADIO_CHANNEL_ACCESS_FAILURE, RADIO_NO_ACK } |
This enumeration defines the possible return values for the TAT API functions. More... | |
| enum | radio_cca_mode_t { CCA_ED = 0, CCA_CARRIER_SENSE = 1, CCA_CARRIER_SENSE_WITH_ED = 2, CCA_ENERGY_DETECT = 0, CCA_CARRIER_SENSE = 1, CCA_CARRIER_SENSE_WITH_ED = 2 } |
This enumeration defines the possible modes available for the Clear Channel Assessment algorithm. More... | |
| enum | radio_clkm_speed_t |
This enumeration defines the possible CLKM speeds. More... | |
Functions | |
| radio_status_t | radio_init (bool cal_rc_osc, hal_rx_start_isr_event_handler_t rx_event, hal_trx_end_isr_event_handler_t trx_end_event, radio_rx_callback rx_callback) |
| Initialize the Transceiver Access Toolbox and lower layers. | |
| uint8_t | radio_get_operating_channel (void) |
| This function will return the channel used by the radio transceiver. | |
| radio_status_t | radio_set_operating_channel (uint8_t channel) |
| This function will change the operating channel. | |
| uint8_t | radio_get_tx_power_level (void) |
| This function will read and return the output power level. | |
| radio_status_t | radio_set_tx_power_level (uint8_t power_level) |
| This function will change the output power level. | |
| uint8_t | radio_get_cca_mode (void) |
| This function returns the current CCA mode used. | |
| uint8_t | radio_get_ed_threshold (void) |
| This function returns the current ED threshold used by the CCA algorithm. | |
| radio_status_t | radio_set_cca_mode (uint8_t mode, uint8_t ed_threshold) |
| This function will configure the Clear Channel Assessment algorithm. | |
| radio_status_t | radio_get_rssi_value (uint8_t *rssi) |
| This function returns the Received Signal Strength Indication. | |
| uint8_t | radio_batmon_get_voltage_threshold (void) |
| This function returns the current threshold volatge used by the battery monitor (BATMON_VTH). | |
| uint8_t | radio_batmon_get_voltage_range (void) |
| This function returns if high or low voltage range is used. | |
| radio_status_t | radio_batmon_configure (bool range, uint8_t voltage_threshold) |
| This function is used to configure the battery monitor module. | |
| radio_status_t | radio_batmon_get_status (void) |
| This function returns the status of the Battery Monitor module. | |
| uint8_t | radio_get_clock_speed (void) |
| This function returns the current clock setting for the CLKM pin. | |
| radio_status_t | radio_set_clock_speed (bool direct, uint8_t clock_speed) |
| This function changes the prescaler on the CLKM pin. | |
| radio_status_t | radio_calibrate_filter (void) |
| This function calibrates the Single Side Band Filter. | |
| radio_status_t | radio_calibrate_pll (void) |
| This function calibrates the PLL. | |
| uint8_t | radio_get_trx_state (void) |
| This function return the Radio Transceivers current state. | |
| radio_status_t | radio_set_trx_state (uint8_t new_state) |
| This function will change the current state of the radio transceiver's internal state machine. | |
| radio_status_t | radio_enter_sleep_mode (void) |
| This function will put the radio transceiver to sleep. | |
| radio_status_t | radio_leave_sleep_mode (void) |
| This function will take the radio transceiver from sleep mode and put it into the TRX_OFF state. | |
| void | radio_reset_state_machine (void) |
| This function will reset the state machine (to TRX_OFF) from any of its states, except for the SLEEP state. | |
| void | radio_reset_trx (void) |
| This function will reset all the registers and the state machine of the radio transceiver. | |
| void | radio_use_auto_tx_crc (bool auto_crc_on) |
| This function will enable or disable automatic CRC during frame transmission. | |
| radio_status_t | radio_send_data (uint8_t data_length, uint8_t *data) |
| This function will download a frame to the radio transceiver's transmit buffer and send it. | |
| uint8_t | radio_get_device_role (void) |
| This function will read the I_AM_COORD sub register. | |
| void | radio_set_device_role (bool i_am_coordinator) |
| This function will set the I_AM_COORD sub register. | |
| uint16_t | radio_get_pan_id (void) |
| This function will return the PANID used by the address filter. | |
| void | radio_set_pan_id (uint16_t new_pan_id) |
| This function will set the PANID used by the address filter. | |
| uint16_t | radio_get_short_address (void) |
| This function will return the current short address used by the address filter. | |
| void | radio_set_short_address (uint16_t new_short_address) |
| This function will set the short address used by the address filter. | |
| void | radio_get_extended_address (uint8_t *extended_address) |
| This function will read the extended address used by the address filter. | |
| void | radio_set_extended_address (uint8_t *extended_address) |
| This function will set a new extended address to be used by the address filter. | |
| radio_status_t | radio_configure_csma (uint8_t seed0, uint8_t be_csma_seed1) |
| This function will configure the CSMA algorithm used by the radio transceiver when transmitting data from TX_ARET_ON state. | |
| bool | calibrate_rc_osc_clkm (void) |
| Calibrate the internal RC oscillator. | |
| void | calibrate_rc_osc_32k (void) |
| Calibrate the internal RC oscillator. | |
This file contains radio driver code.
Definition in file radio.h.
1.6.1